Get a Repair Quote
Free tool

Pool Pump Calculator: Size, Running Cost and Payback

Find the right flow rate and horsepower for your pool, then see what your pump costs to run each year and how fast a variable-speed pump pays for itself. No email required.

What size pump do you need?

Recommended flow
42 GPM
Pump size
1.5 HP VS

Estimate only. Filter type, pipe diameter and fitting count also matter; a local pro can confirm on site.

Shop pumps in this size

Match the flow and horsepower above, then compare a few variable-speed models side by side before you buy.

Compare variable-speed pumps on Doheny’s See variable-speed pump prices on Amazon

PoolPump.com earns a commission if you buy through these links. Your price stays the same. Affiliate disclosure.

What does your pump cost to run?

Your current pump, per year$0
Variable-speed pump, per year$0
You would save, per year$0
Payback time0 months
Energy used, before and after (kWh/yr)0 / 0

Uses typical electrical draw for each single-speed size and the pump affinity laws (power drops roughly with the cube of motor speed), with a conservative adjustment for low-speed motor losses. Your bill shows your real rate.

Email me these results

Get your numbers plus the pool pump replacement checklist (sizing, rebates, what to check before you buy).

No spam. Unsubscribe anytime.

Key takeaways

  • Flow rate in GPM = pool gallons divided by (turnover hours x 60). A 20,000-gallon pool on an 8-hour turnover needs about 42 GPM.
  • Halving a pump's speed cuts its power draw to roughly one-eighth, which is why a variable-speed pump running longer and slower uses far less electricity.
  • At 17 cents per kWh, a 1.5 HP single-speed pump running 8 hours a day for 7 months costs about $490 a year. A variable-speed pump moving the same water over 12 hours costs about $220, a 55 percent cut.
  • A $1,500 installed variable-speed pump on a 1.5 HP pool pays for itself in about 5 to 6 seasons; a year-round pool, a bigger old pump or a utility rebate cuts that to 2 to 4.

How the sizing math works

Pool professionals size circulation around turnover: the time it takes to push your whole pool volume through the filter once.

GPM = Pool Gallons / (Turnover Hours x 60)

Most residential pools target an 8-hour turnover. The horsepower figure is a starting range: the pump's rated flow at your plumbing's head pressure (pipe size, fittings, elevation) decides real performance, which is why two pumps with the same HP label can perform differently.

Pool pump size chart

The flow you need is your pool's volume divided by how fast you want to turn it over. Most residential pools aim for one full turnover in 8 hours; a heavily used or warm-climate pool often runs 6. Find your gallons, read across, and that is the minimum flow (in gallons per minute) the pump has to deliver at your system's resistance.

Pool volume (gallons)6-hour turnover8-hour turnover10-hour turnover
5,00014 GPM10 GPM8 GPM
10,00028 GPM21 GPM17 GPM
15,00042 GPM31 GPM25 GPM
20,00056 GPM42 GPM33 GPM
25,00069 GPM52 GPM42 GPM
30,00083 GPM63 GPM50 GPM
40,000111 GPM83 GPM67 GPM
50,000139 GPM104 GPM83 GPM

Horsepower is the last thing to pick, not the first. Take the GPM from this chart and check it against the manufacturer's pump curve at your plumbing's head; the calculator above turns the same flow into a starting horsepower range.

How the running-cost math works

A pump's yearly cost is its electrical draw in kilowatts, times hours per day, times days of the season, times your rate. Single-speed pumps always run at full speed, so the only lever is hours. A variable-speed pump changes the other lever: speed. Under the pump affinity laws, flow falls in step with speed but power falls with roughly the cube of speed, so moving the same water slowly over more hours uses a fraction of the energy.

Typical yearly cost by pump size

Single-speed pump, 8 hours a day, 7-month season, 17 cents per kWh, against a variable-speed pump moving the same water over 12 hours:

Single-speed sizeTypical drawSingle-speed / yrVariable-speed / yrSaved / yr

Typical draws are representative wire-to-water figures for older single-speed motors; check your pump's label for exact amps and volts (watts = amps x volts). Table values are calculated live by the same formula as the calculator above.

Check for a rebate before you buy

Many electric utilities pay a rebate on qualifying variable-speed pool pumps, and amounts change every year. Search your utility's website for "pool pump rebate", or ask the installer to check when you get a replacement quote. Put the amount in the calculator to see your real payback. For models and prices, see our variable-speed pool pump guide and buying guide.

Add this calculator to your site

Run a pool blog, pool service company or energy site? Paste this code into any page. It is free, needs no account, and stays up to date.

Common questions

Calculator FAQ

A 1.5 HP single-speed pump draws about 1.7 kW. Running 8 hours a day at 17 cents per kWh, that is about $2.30 a day, or roughly $490 over a 7-month season. Year-round pools in warm states pay closer to $850.

Usually 50 to 70 percent of the pump's electricity, because it moves the same water at low speed, where power draw drops sharply. Savings are largest when the old pump is oversized or runs long hours.

An oversized single-speed pump pushes water faster than the filter and plumbing were designed for. It wastes energy, wears fittings and filter media faster, and adds nothing to water quality.

Rectangular pool: length x width x average depth x 7.5. Round pool: diameter x diameter x average depth x 5.9. Oval: length x width x average depth x 5.9.

Yes. Copy the embed code above and paste it into any page. It is free and needs no sign-up.